A dripping tap in Port Elizabeth costs you twice: once on the water bill and once on your sleep. Those are the two reasons it is worth fixing rather than living with. The good news is that a drip is usually not the tap giving up. It is a small part inside it that has worn, and often the job is that part and nothing more.
Here is what the repair costs, why the type of tap you have decides the amount of work, and the honest line between what a handyman can do and what has to go to a registered plumber.
Why a drip is worth fixing early
A drip is small enough to ignore and steady enough to matter. Water running away while nobody is using the tap is water you are paying for, and it does not stop when you go to bed. A tap dripping into a basin overnight also has a way of waking the whole house, and in a rental it turns into a message from a tenant within a week.
There is a second reason that has nothing to do with the bill. A worn washer does not simply leak. It sits badly, and the water then eats at the edge of the tap seat underneath it. Fixed early, that is a washer. Left for a long time, the seat itself can be marked, and the repair stops being the same job. A tap that has dripped for a year or two is not the same repair as one that started dripping last month, and it is worth knowing that before it drifts.
Washer, cartridge or ceramic disc decides the job Coastal homes deal with this faster. Around Summerstrand and Humewood the salt air works on the inside of a tap the same way it works on hinges and gate hardware, so a cartridge that has spent years near the sea can be pitted and rough rather than simply worn, and that is worth knowing before the part is ordered.
- Washer taps. The traditional type, and still the most common in older Gqeberha homes. Turning the handle presses a rubber washer down onto a seat, and the washer is what wears out. Usually the quickest of the three to sort.
- Cartridge and ceramic disc taps. Modern quarter turn or half turn taps, where a cartridge or a pair of ceramic discs controls the flow. There is no washer to change, so the correct part has to be matched to the tap. A photo of the tap and any branding on it saves a wasted trip.
- Mixer taps. Hot and cold in one body, which means two inlets and often one cartridge controlling both. More parts inside, and a drip can come from either side of the mix.
The type decides how long the job takes and whether the part can be found the same day. A common washer is a stock item. A cartridge for a specific imported tap may need to be tracked down first, and that is the difference between an hour and a follow up visit. One more thing, said plainly: a tap that has already been opened up and put back together with the wrong part is harder to sort than one nobody has touched.
What it costs The same goes for age. A tap that has never been opened is predictable; a tap with a rounded off head and a previous repair hidden inside it is not, and honesty about that is cheaper than a second visit.
- Dripping tap or washer replaced: R350 to R650
- Toilet fill or flush valve replaced: R400 to R750
- Toilet seat replaced: R250 to R500
- Silicone redone on a bath or basin: R450 to R800
Washers, cartridges, seats and valves are materials, so they are quoted separately and approved before anything is bought. The job price itself is fixed before work starts and does not move unless you change what you want done. Toilets and silicone appear in the same list because they are the same kind of work, a fitting rather than pipework, and they are usually worth doing on the same visit as the tap.
Where a handyman stops and a plumber starts
This is worth being blunt about, because getting it wrong wastes a visit for everyone involved. A tap, a toilet, a washer, a cartridge, a seat and a fill valve are fittings on the end of a pipe. The handyman side ends there.
- Taps, toilets, washers, cartridges, seats and fill valves: handyman work.
- Pipework, geysers, buried drainage and anything on the water supply beyond a fitting: a registered plumber.
- Fixed electrical work, including new sockets, circuits and anything needing wiring: a registered electrician.
Working out which one you have is easier than it sounds. If the water shows up at the tap, at the toilet, or at a joint you can see under the basin, it is a fitting and it is in scope. If water is appearing where no fitting is visible, at the base of a wall, on a ceiling below the bathroom, or around a geyser, then the problem is in the pipework or the geyser and it is not a handyman job. Photograph it and say where the water is, and you get told which trade to call instead of being booked for work that is out of scope.
When a drip is a bigger problem in disguise
Some drips are exactly what they look like. Others are the visible end of something else, and these are the ones that turn out not to be a washer at all.
- Water at the base of the toilet rather than inside the bowl, which is usually the seal between the pan and the floor rather than the cistern.
- Water pooling inside a vanity cupboard under the basin, which points at the waste or the trap rather than the tap itself.
- A tap that only drips while it is running, which is more often a worn cartridge or a loose connection than a washer.
- A cistern that runs on and will not stop, which can be the fill or flush valve but is sometimes the overflow instead.
- Water in the drip tray under a geyser, or a drip appearing on a ceiling below the bathroom, which is the point to stop and call a registered plumber.
The point of that list is not to turn you into a plumber. It is so that the first message you send describes where the water actually is, because that decides the trade and the price before anyone travels.
Worth mentioning when you send the photo: a tap that has dripped for months often leaves a stain ring on the basin or bath and lifts the sealant behind the tap. That is usually a few minutes of the same visit if it is flagged in advance, and a separate booking if it is discovered on the day.
The short version
The type of tap decides the repair: a washer is quick, a cartridge or ceramic disc has to be matched to the tap, and a mixer has more parts inside it. Taps, toilets, washers, cartridges, seats and fill valves are handyman work, while pipework, geysers and buried drainage belong to a registered plumber and fixed electrical work belongs to a registered electrician. If the water is showing up somewhere other than a fitting, say so in the first message, because it changes who you need rather than how much the job costs. Send a photo of the tap, a photo of where the water is and where it is dripping from, and you get a fixed price back on WhatsApp before anything is booked.
Got a list that needs working through?
Send it on WhatsApp with a photo or two and you get a price back, before anything is booked.
Send the list