Skip to content

Gqeberha

067 397 3341
Pools

Pool pump not working: the eight faults and what each one costs

7 min read · Gqeberha

A pool pump fails in one of three ways. It is silent when it should be running, it hums without moving water, or it runs but the pool stays cloudy and the pressure gauge has drifted somewhere it should not be. Each of those points at a different fault, and the difference between them is the difference between a cheap repair and an unnecessary replacement.

This is what each fault is, how to tell them apart before anyone is called out, and what the fix costs in Gqeberha. Prices are per job, not per hour, and materials are quoted separately and approved before anything is bought.

The two-minute check before anything else

Open the pump lid and look. Then work through this in order, because it eliminates most of the expensive answers in under five minutes.

  • Is there power at the plug or isolator? Test the circuit breaker and the earth leakage, not just the switch on the pump.
  • Is the timer or control box set to run now? A pump that "stopped by itself" is often a timer that was never reset after a power failure.
  • Is the water level above the skimmer mouth? A pump pulling air is doing exactly what it was told.
  • Is the weir flap moving freely and the basket clear? A blocked basket starves the pump even when it looks fine from above.
  • Is the lid O-ring seated and the lid tight? A lid that is one turn loose will never hold prime.

If all five pass, the fault is in the pump or the line, and the list below is where to look.

One: no power at all

Silence, no hum, nothing. This is almost always electrical upstream of the pump: a tripped breaker, a failed timer, a burnt plug point, or an earth leakage that tripped because of moisture in the pump housing.

A handyman can test and replace a plug point, and can tell you whether the circuit is dead to the pump. Anything beyond the plug and isolator is fixed electrical work and belongs to a registered electrician, because the circuit feeding a pool pump sits outdoors next to water and gets no second chances.

Two: humming, not spinning

The pump is getting power but the shaft is not turning. There are two usual causes.

The first is a capacitor that has failed, which is a small part and a quick job. The second is a seized shaft or a jammed impeller, which is what happens when the pump sat switched off for a season with water inside, or when debris got past a broken basket.

Do not leave it humming and walk away. A pump held on a stalled motor overheats the windings, and a motor that was repairable becomes a replacement.

Three: running but not priming

The pump spins, moves some water, then loses it. Air is being pulled in on the suction side, and the leak is almost always one of these four:

  • The lid O-ring, which goes hard and flat in the sun and stops sealing.
  • The pump lid itself, cross threaded or not tight.
  • A joint on the suction pipe between the skimmer and the pump, often a union or an elbow that has been slowly sucking air for months.
  • A non-return valve or a skimmer line that has lost water because the level dropped too far.

Priming failures are diagnostic jobs. The part is usually the cheapest thing in the repair, and the value is in finding which of the four it is rather than in the part itself.

Four: a blocked impeller

The pump runs, prime is poor, and the flow at the return eyes is weak. Pull the basket and look into the impeller through the pump mouth. Leaves, hair, acacia seed pods and the occasional piece of pool glass all collect there.

Clearing an impeller is part of a service, not a rebuild. If the pump has been run with a broken basket, expect damage to the impeller itself, which is where the cost moves up. Our published range for a pump seal, O-rings or impeller replacement is R900 to R1,800, and that is the job that covers it.

Five: worn seals and a drip under the pump

Water under the pump body, or a mechanical seal that has started to weep, will take out a motor bearing within a season. This is the cheapest moment to deal with it.

Seals, O-rings and impellers are the same R900 to R1,800 range. Left alone, the same fault becomes a motor replacement, and the motor is the expensive part of a pump.

Six: the pump is fine, the filter is not

The pump runs well, the water is cloudy, and the pressure gauge sits high. That is a filter problem being blamed on the pump. Backwash first, watch the sight glass, and if the pressure stays high or climbs again within days, the media is spent.

Filter sand or media replacement is R900 to R2,200 with us, and it is the single most neglected job on a residential pool. A filter carrying old media passes fines back into the pool, which is why people buy algaecide all summer and never solve it.

Seven: a blocked suction line

The pump loses prime every time it stops, or pulls hard and then gives up. A blockage in the skimmer line, a stuck non-return valve, or a collapsed section of suction pipe all behave this way.

This one is sometimes a rodding job and sometimes a digging job, and the site visit decides which. It is worth being honest that this is the fault most likely to change the price once someone is on site.

Eight: the motor itself

Overheating, tripping the breaker, or a burnt smell. At this point the question stops being repair and becomes replace, because a rewind on a small pool pump rarely makes financial sense against a new unit.

A replacement pump is a supplier purchase quoted separately, and the install labour sits in the same bracket as the seal job. What we will not do is sell you a motor when the fault was a capacitor in fault two, which is why the elimination order above matters.

Why pumps fail in the first hot week

There is a pattern to when these calls come in, and it is worth knowing because most of it is preventable.

The first properly hot week of summer does three things at once. Evaporation drops the water level below the skimmer mouth, so the pump starts pulling air. The wind that comes with a Gqeberha November fills the baskets with leaves and seed pods faster than anyone checks them. And the pool gets used daily for the first time since April, which stirs up everything that settled over winter and loads the filter.

A pump running dry does not fail immediately. It runs hot, the seal hardens, and then one afternoon it hums instead of spinning. That is the whole story behind most of the pumps we replace in December.

Checking the water level every second day and emptying the basket before anyone swims costs nothing and removes the majority of these faults.

A service is not a repair

These get confused, and the difference matters when you are deciding what to spend.

A service is the routine work: clean the basket, check the lid and O-ring, clear the impeller, brush and vacuum the pool, check the chemistry, backwash and confirm the pressure after backwash. It is the work that keeps a pump alive.

A repair is what happens when one of the eight faults above has already occurred. Seals, impellers, valves, media.

If you have never had the pump serviced and it has been running three seasons, the honest recommendation is a service before a fault, not a repair after one. The parts that fail are the parts a service checks.

What this costs, in one place

Published per-job ranges for the work we do on pools:

  • Pool cleaned, vacuumed and brushed: R350 to R800
  • Filter sand or media replaced: R900 to R2,200
  • Pool pump seal, O-rings or impeller replaced: R900 to R1,800
  • Diagnosis and clearing of a priming or blockage fault: quoted on site, because the cause decides the work

Materials and fittings are quoted separately and approved by you before anything is bought.

What is not a handyman job

Fixed electrical work, which means anything past the plug, the isolator and the pump's own flex. A pool pump circuit needs a registered electrician and a certificate of compliance when it is installed or altered, and we will tell you that rather than take the work.

Motor rewinds and pump body damage belong to a pool equipment specialist. What we do is everything around that: baskets, lids, O-rings, seals, impellers, media, priming faults, blockages and the routine clean that stops half of these faults happening.

The two-minute check at the top of this page removes most of the expensive answers. Send the model number and a photo of the pressure gauge on WhatsApp, and the first visit is usually the only one.

How to book it

Get the model number off the pump, take a photo of the pressure gauge, and note what it does when it starts. That is three minutes of work and it usually means one visit instead of two.

WhatsApp 067 397 3341 with the photo and a description. A pool pump that is humming, silent, or losing prime is worth sorting in November rather than in the week before Christmas, when everyone in Gqeberha discovers their pool at the same time.

Got a list that needs working through?

Send it on WhatsApp with a photo or two and you get a price back, before anything is booked.

Send the list

More advice

The suburbs

Bluewater Bay, Seaview and Beachview: why a list beats a quick call-out

A single dripping tap is not worth the drive out to Beachview. A list of six jobs is. How north coast visits are planned and what tends to fail there.

Read it

Fittings

Shelves that actually hold: brackets, plaster and the weight question

Almost every shelf failure comes down to the bracket being chosen for the look rather than the wall. How to drill into the wall you actually have.

Read it

Pools

Getting the pool ready for December: the six-week plan

Recovery is a sequence, and it takes weeks because chemistry and filtration work on time. The six-week plan that makes December easy.

Read it

Pools

Pool filter sand and cartridges: the service most pools skip

A pool filter fails so slowly nobody notices until the water never quite clears. The signs, the media types, and what replacing it costs in Gqeberha.

Read it

Rentals

Landlord turnarounds in Lorraine, Framesby and Kabega Park: the punch list that gets the deposit back

The move-out punch list that gets a Gqeberha deposit back: room by room, what counts as wear and tear, the five repairs that cost tenants, and how to time a turnaround.

Read it

Assembly

A wardrobe and a bed, assembled: what breaks and what it costs to put right

A two door wardrobe and a bed base are the two items most often half-assembled. What each costs, the failures that break them, and when to rescue rather than replace.

Read it

Tiling

Tile over tiles or strip first? What each costs in Port Elizabeth

Tiling over an existing floor is faster and cheaper on paper. Here is when it is legitimate, what the height does to doors and skirtings, and what stripping really adds.

Read it

The suburbs

Older homes in Newton Park, Charlo and Mount Croix: the jobs that keep coming back

The older inner suburbs of Port Elizabeth share the same tired fittings. The five jobs that repeat across the area, what each costs, and how to batch them into one visit.

Read it

Plumbing

A toilet that keeps running: what it costs to fix

A running toilet has four causes and a two-minute diagnosis. Which part to replace, what it costs, and when it becomes a plumber's job.

Read it

Assembly

Flat pack assembly: time, tools and the parts that break

What is actually in the box, the tools that matter, where the time goes, and the four failures that turn a one visit job into two in Gqeberha.

Read it

Tiling

Tiling in Port Elizabeth: what it costs per square metre in 2026

The per square metre price is the most quoted number in tiling and the least useful one. Here is what the published ranges cover, and how to get a real figure.

Read it

Areas

A handyman visit in Summerstrand, Walmer and Newton Park

Three suburbs minutes apart, three different kinds of job. What salt air does on the beachfront, what older houses need in the centre, and what a visit covers.

Read it

Painting

Painting touch-ups after a repair: why the patch shows

A touched up patch almost always shows, even when the colour matches. What the wall has done to the old paint, and how far back a repair has to go.

Read it

Roofing

Roof leak repair in Port Elizabeth: what it costs in 2026

Roof work is the least predictable job on any list. What the money actually goes into, and what a leak costs to repair in Gqeberha.

Read it

Waterproofing

Roof waterproofing in Port Elizabeth: priced per job, not per square metre

Why this site prices a waterproofing job rather than a square metre, where tiled roofs actually fail on the coast, and what the work costs.

Read it

Doors

Why your door sticks in winter, and why sanding it makes next winter worse

A sticking door is the timber moving with the seasons, not the timber being too big. Sanding the edge clears it now and sets up next winter's return.

Read it

Scope

What a handyman can and cannot legally do in South Africa

The one line that decides whether a job is handyman work or a registered trade, and how to read the answer before you book anyone.

Read it

Assembly

Flat pack furniture assembly in Port Elizabeth: what it costs per item

Flat pack furniture is priced per item, not per box. What a bed and a wardrobe cost to assemble in Port Elizabeth, and why a missing fitting stalls the job.

Read it

Doors

Hanging a door in Port Elizabeth: what it costs and what is involved

A door is a slab of timber going into a frame that has had decades to move. What the job actually involves, and what it costs in Gqeberha.

Read it

Leaks

Water coming through the ceiling: what to do in the first hour

What to do in the first hour when water starts coming through a ceiling, why poking the bulge is a mistake, and how the leak is traced back to its actual source.

Read it

Landlords

A rental maintenance checklist for Gqeberha landlords and agents

Running a rental on a checklist instead of on complaints means one planned visit instead of five separate ones. The list, and what it costs.

Read it

Fitting

Curtain rails and blinds in Port Elizabeth: who fits them and what it costs

Shops sell the rail, the blind and the shelf, then leave you to fit them. What fitting costs per window in Port Elizabeth, and why the wall decides the fixing.

Read it

Small plumbing

A dripping tap in Port Elizabeth: what it costs and when it needs a registered plumber

A dripping tap costs you on the water bill and on your sleep. What the repair costs in Port Elizabeth, and where the plumber has to take over.

Read it

TV mounting

TV wall mounting in Port Elizabeth: what it costs and which wall you have

One number decides most of the price before anyone arrives: what your wall is made of. How to check, and what fitting a bracket actually comes to.

Read it

Odd jobs

No job too small: the odd jobs a handyman actually does

The hardest job to get done in a house is never the big one, it is the single small thing. Here is the actual list, and why batching them pays.

Read it

Coastal

Salt air and rust: what coastal Gqeberha does to doors, windows and fittings

Salt air corrodes the fittings that hold a coastal home together. What the sea does to doors, windows and gate hardware in Gqeberha, and what the repairs cost.

Read it

Cupboards

The cupboard hinge that pulled out of the chipboard

Once the screw holes in chipboard strip, tightening the same screw never works again. Here is which repair holds, and what it costs in Gqeberha.

Read it

Pricing

What a handyman costs in Gqeberha

What the common jobs actually cost in Gqeberha in 2026, why an hourly rate is a bad deal for the person paying, and how to judge a quote you have been handed.

Read it

The list

The small-job list: twelve things worth booking in one visit

The jobs that sit on the fridge door for a year. How long each one takes, which ones belong in one visit, and how to split a long list sensibly.

Read it

Complexes

Complex access: what to have ready before a handyman arrives

Access registers, POPIA requirements, noise hours and lift rules. The details that decide whether a booked visit starts on time or stalls at the boom.

Read it

Send the list. Get a price. Get it done.

One or twenty jobs, it makes no difference. The more you put on the list, the better the visit works out.

WhatsApp your listCall 067 397 3341

No price is agreed until you approve it

Call nowGet a quote