Salt air corrodes metal a little every day, and the first things it takes are the fittings that hold doors and windows together. In Gqeberha the sea is rarely more than a few minutes away, so homes in Summerstrand, Humewood and Mill Park sit in a mild salt bath all year, whether or not they can see the water. It is not a dramatic problem. It is a patient one, and it shows up on the small metal parts long before it shows up anywhere else. Nothing rusts through overnight, which is exactly why so much of it gets ignored until a door will not close.
The damage arrives quietly. A hinge starts to grind, a handle feels rough in the hand, a door that used to close with a click now needs a shoulder. By the time rust is visible it has usually been working for a season or two underneath the surface. This is what salt actually does to a coastal house, which parts fail first, why the fixings matter more than the fittings themselves, and what those repairs cost.
What salt air actually does to a house
Air near the sea carries salt as fine particles of spray. They settle on every surface, and salt holds moisture, so metal that stays slightly damp and slightly salty starts to corrode. Once rust gets under a plated finish it keeps working underneath it, flaking the coating from below while the outside still looks almost intact. That is why a coastal hinge often looks perfectly fine right up to the moment it shears, and why painting over rust without removing it properly achieves very little.
Distance matters less than people expect. Schoenmakerskop and Sardinia Bay are obviously exposed, and Summerstrand and Humewood sit right in the thick of it, but the salt reaches Walmer, Lovemore Heights and even the Northern suburbs on a hard south easterly. The sea facing side of a house collects far more of it than the side that faces away, so two identical doors on opposite walls can be years apart in condition. Shaded, poorly ventilated corners suffer worst, because moisture lingers in them instead of drying off, and a dripping gutter or a leaking downpipe on that side of the house makes it worse.
The parts that go first
- Door hinges, especially the plated ones that come standard on cheaper doors and kitchen cupboards
- Handles, latches, letterboxes and house numbers on any wall within reach of the sea wind
- Gate hardware, including hinges, drop bolts and latches, all handled daily and all fully exposed
- Window stays, catches and the small screws holding frames, sills and aluminium sections together
- Anywhere two different metals touch, where moisture and dissimilar metals speed each other up
The same fittings inside a house last years longer, simply because the air is drier and the salt has less chance to settle on them. That is why coastal repair work is so often external, or on the doors and windows that open to the outside. It also explains how a front door on the sea side can need new hinges and a rehang while the internal doors two metres away are still perfectly sound and closing cleanly. If you are working through a house, it usually makes sense to start at the sea facing side and work inwards.
Why stainless and galvanised fixings are not optional on the coast
Coastal repairs get stainless or galvanised fixings by default, not as an upgrade. A standard plated screw in a coastal door can be rusted solid within a season, and the fittings cost a fraction of the labour to go back in and redo the job properly.
That one choice decides whether a repair lasts. A hinge is only as good as the screws holding it, and galvanised steel resists salt far better than bright zinc plating. Stainless is better again, and on a wall within reach of the sea wind it is usually the right answer. The difference in cost on a packet of screws is small next to the cost of going back into the same door a year later, and that is the whole argument for doing it once and doing it with the right hardware. The same logic applies to any fixing that has to survive outside, from a gate bolt to a door frame screw.
Doors and windows: humidity plus salt
Coastal door problems are usually two faults at once. The salt eats the hinge and the humidity swells the timber. A swollen door drags at the bottom or the lock side, and once a hinge has also corroded the door starts to sag as well, so the top corner catches and the lock stops lining up. Fix the sticking and ignore the hinge and you are back where you started within weeks. Fix the hinge and ignore the swelling and the same thing happens in the opposite direction. Windows behave the same way at the frame and the catch, and a window that has gone stiff to open is usually a corroded stay or a swollen frame rather than a broken one, which is why forcing it tends to crack the frame instead of fixing the cause. The honest answer for either one is to deal with the metal and the timber in the same visit, even when only one of them looks like the problem.
Hinges, handles and gate hardware
- Hinges replaced with galvanised or stainless units: R200 to R380
- Cupboard door rehung on new hinges: R250 to R500
Gate hardware is the part of coastal work that gets left longest, because a stiff latch is annoying rather than urgent, and it is also the part most exposed to the weather. A drop bolt that has seized is a quick job to replace and a hazard in the meantime. Replacing latches, hinges and drop bolts with galvanised or stainless versions is handyman work. Gate motors and automation are not, and those get referred to a specialist.
Paint that lifts, and what the repair costs
Paint on a coastal wall blisters and lifts for the same reason doors go stiff. Salt and moisture get behind the film, and once they are trapped under it the paint lets go from the surface rather than wearing away, so you get soft patches that scrape off in sheets and take the topcoat with them. On a coastal wall the failure usually starts low down, where splash and ground moisture meet the salt the wind has left behind. Painting over the top without sorting the cause buys a few more months and then fails in exactly the same place. Preparation is most of this job, and it is the part that cannot be rushed to save a day. Materials and fittings are quoted separately and approved before anything is bought, so the figures below are for the work itself.
- Sticking door adjusted: R280 to R500
- Door planed and refitted: R400 to R650
- Wall patch filled and painted: R300 to R700
- Skirtings cleaned and repainted: R600 to R1,200
The short version
Salt air is manageable. Fix the metal and the timber in the same visit, use galvanised or stainless fittings, and the same job does not come back next season. The parts that fail first are always the small ones, and they are always cheaper to deal with before they take something more expensive with them. A hinge is a small job. A frame that has split because a door was forced is not.
If a coastal door is dragging, a hinge has gone rough or a gate latch has finally seized, send a photo on WhatsApp along with the frame or wall the item sits in. You get a fixed price back before anything is booked, and materials are priced separately so nothing is bought without your approval.
Got a list that needs working through?
Send it on WhatsApp with a photo or two and you get a price back, before anything is booked.
Send the list