Skip to content

Gqeberha

067 397 3341
Plumbing

A toilet that keeps running: what it costs to fix

6 min read · Gqeberha

You hear it at night in a Gqeberha home: a cistern that refills itself every twenty minutes, or a constant thin trickle into the pan that you stop noticing after a week. It is one of the cheapest repairs in a house and one of the most ignored, and an ignored one keeps working on your water bill long after you have stopped hearing it.

A running toilet only has four causes, and you can usually work out which one it is in two minutes with the lid off.

How the cistern actually works

Three parts, and every running toilet is one of them failing.

The fill valve lets water in and stops when the float reaches its set height. The flush valve, sometimes a flap and sometimes a drop valve, lifts when you press the button and then closes to seal the outlet. The overflow is the safety: if the fill valve never shuts off, water escapes down the overflow pipe into the pan instead of onto the floor.

Understanding that order matters, because it tells you what a trickle into the pan means. Water entering the pan when nobody has flushed is either a flush valve that is not sealing, or a fill valve that is set so high the cistern runs into the overflow.

The two minute diagnosis

Lift the lid and watch what happens after a flush finishes.

  • Water stops, then starts again a few minutes later with no one touching it. The flush valve seal is passing. Water leaks out, the level drops, the fill valve tops it up. That cycle is the noise at night.
  • A visible trickle into the pan that never stops. Again the flush valve seal, or a drop valve that is not seating because of grit or scale on the seat.
  • Water running into the overflow pipe. The fill valve is not shutting off, or the float has been set too high, or the arm is catching on something inside the cistern.
  • The cistern will not fill at all. Not a running toilet but the same parts: a blocked inlet filter or a dead fill valve.

A dye test settles it when you cannot see the trickle. Put a few drops of food colouring in the cistern, leave it twenty minutes without flushing, then look in the pan. Colour in the pan means the seal is passing.

Cause one: the flush valve seal

The cheapest fix in plumbing. A rubber seal that has gone hard, grown a film of scale, or been cut by a piece of grit.

On a flap style valve, the seal is a rubber disc that lifts out. On a drop valve it is a ring around the base. Either way the part costs very little and the job is minutes once the water is off.

If the seat itself is rough or scaled, clean it before fitting the new seal, or the new one will fail the same way within a month.

Cause two: the fill valve

The valve fails to shut off, so the cistern keeps filling and dumps the excess down the overflow. Symptoms are a hiss that never stops and water visibly running into the overflow pipe.

A fill or flush valve replacement with us is R400 to R750, and it is one of the highest value small jobs in a house, because a valve that will not shut off is wasting water continuously.

The cheaper alternative, replacing just the washer inside the valve, works when the valve body is sound. It does not work on the sealed cartridge types that most modern cisterns use, and that is the point where the whole valve gets replaced.

Cause three: float height and obstruction

Before buying anything, look at the float. If the water level is set so high that it sits at the overflow mouth, the cistern will run into the overflow forever, no matter how good the valve is.

Adjusting the height takes a minute. The same minute catches the other version of this fault: a float arm catching on the inlet pipe, a piece of scale, or the edge of the cistern lid.

Most people who buy a valve and find the problem unchanged have skipped this check.

Cause four: the seat and the pan connector

Less common, and it shows differently. If the water on the floor is at the base rather than running into the pan, the fault is the pan connector or the seal between the pan and the floor, not the cistern at all.

That is a different job and a different set of parts, and it is worth checking before assuming a running noise is a cistern problem.

The parts, and how to buy the right one

A cistern has far fewer parts than it looks like it has. Before you buy anything, take a photo of the inside of the cistern with the lid off. The valve type is what decides which seal or cartridge you need, and there are several that look similar from above.

Three things are worth knowing at the shop:

  • Flap valves and drop valves use different seals. They are not interchangeable, and a seal that "looks about right" will leak again within a week.
  • Sealed cartridge fill valves cannot be repaired, only replaced. If the top of the valve is a sealed unit with no visible washer, stop trying to fix it.
  • Buy the same brand as the valve in the cistern if you can. Mixing brands inside one cistern is where alignment problems start.

A photo at the counter saves a second trip, and a second trip is what turns a fifteen minute job into a week of a running toilet.

Turning the water off, and back on

Every cistern has an isolation valve, usually a small screwdriver slot on the supply pipe below the cistern, or a tap on the wall. Turn it clockwise until it stops. If there is no isolator, the house main has to come off, which is worth knowing before you start rather than halfway through.

Flush once after isolating to empty the cistern, then sponge out what is left so the new seal goes onto a clean, dry seat. Fit the part, turn the water back on slowly, let the cistern fill, and watch one full flush before you put the lid back.

If the cistern will not stop filling after that, the fill valve needs setting or replacing, and that is the point to stop rather than to keep adjusting.

What it costs

Published per-job ranges for the work we do:

  • Toilet seat replaced: R250 to R500
  • Toilet fill or flush valve replaced: R400 to R750
  • Silicone redone on a bath or basin: R450 to R800
  • A dripping tap washer replaced: R350 to R650

Materials and fittings are quoted separately and approved before anything is bought. A new valve is usually the main cost in the job, and there is no benefit in buying the cheapest one twice.

When it becomes a plumber's job

A cistern is a self-contained unit and most of it is handyman work. What is not:

  • Altering or replacing supply pipework inside the wall or under the floor.
  • Moving a toilet, which means drainage and a new pan connector position.
  • Anything involving the geyser, the main supply or the pressure reducing valve.
  • Work that needs a certificate of compliance.

We will tell you when a job crosses that line rather than take it and hope. It is the same boundary that applies to electrical work, and it exists because a botched drain is expensive to fix and a botched cistern is merely annoying.

Why it is worth doing now

A running toilet is a constant, low-level water loss. You will not see it as a spike on a bill the way you would see a burst pipe, which is exactly why it runs for months. What you will see, eventually, is a valve that has been cycling thousands of times and a cistern that needs a full rebuild rather than a seal.

It is a fifteen minute job that most people defer for a year.

Not sure if it is the seal or the overflow? Put a few drops of food colouring in the cistern and leave it twenty minutes without flushing. Colour in the pan means the seal is passing.

Do it with the rest of the list

This is the classic single-item booking that is hard to justify on its own, and the reason to batch it. A running toilet and a dripping tap together are one visit. Add the loose cupboard hinge, the door that sticks and the toilet seat that rocks and you have turned four annoyances into one hour of work.

WhatsApp 067 397 3341 with what the cistern is doing and a photo of the inside of the valve if you can get one. It usually means the right part arrives on the first visit.

Got a list that needs working through?

Send it on WhatsApp with a photo or two and you get a price back, before anything is booked.

Send the list

More advice

The suburbs

Bluewater Bay, Seaview and Beachview: why a list beats a quick call-out

A single dripping tap is not worth the drive out to Beachview. A list of six jobs is. How north coast visits are planned and what tends to fail there.

Read it

Fittings

Shelves that actually hold: brackets, plaster and the weight question

Almost every shelf failure comes down to the bracket being chosen for the look rather than the wall. How to drill into the wall you actually have.

Read it

Pools

Getting the pool ready for December: the six-week plan

Recovery is a sequence, and it takes weeks because chemistry and filtration work on time. The six-week plan that makes December easy.

Read it

Pools

Pool filter sand and cartridges: the service most pools skip

A pool filter fails so slowly nobody notices until the water never quite clears. The signs, the media types, and what replacing it costs in Gqeberha.

Read it

Rentals

Landlord turnarounds in Lorraine, Framesby and Kabega Park: the punch list that gets the deposit back

The move-out punch list that gets a Gqeberha deposit back: room by room, what counts as wear and tear, the five repairs that cost tenants, and how to time a turnaround.

Read it

Assembly

A wardrobe and a bed, assembled: what breaks and what it costs to put right

A two door wardrobe and a bed base are the two items most often half-assembled. What each costs, the failures that break them, and when to rescue rather than replace.

Read it

Tiling

Tile over tiles or strip first? What each costs in Port Elizabeth

Tiling over an existing floor is faster and cheaper on paper. Here is when it is legitimate, what the height does to doors and skirtings, and what stripping really adds.

Read it

The suburbs

Older homes in Newton Park, Charlo and Mount Croix: the jobs that keep coming back

The older inner suburbs of Port Elizabeth share the same tired fittings. The five jobs that repeat across the area, what each costs, and how to batch them into one visit.

Read it

Assembly

Flat pack assembly: time, tools and the parts that break

What is actually in the box, the tools that matter, where the time goes, and the four failures that turn a one visit job into two in Gqeberha.

Read it

Tiling

Tiling in Port Elizabeth: what it costs per square metre in 2026

The per square metre price is the most quoted number in tiling and the least useful one. Here is what the published ranges cover, and how to get a real figure.

Read it

Pools

Pool pump not working: the eight faults and what each one costs

A pool pump fails in one of three ways: silent, humming, or running without moving water. The two-minute check finds the fault, and each repair is priced per job.

Read it

Areas

A handyman visit in Summerstrand, Walmer and Newton Park

Three suburbs minutes apart, three different kinds of job. What salt air does on the beachfront, what older houses need in the centre, and what a visit covers.

Read it

Painting

Painting touch-ups after a repair: why the patch shows

A touched up patch almost always shows, even when the colour matches. What the wall has done to the old paint, and how far back a repair has to go.

Read it

Roofing

Roof leak repair in Port Elizabeth: what it costs in 2026

Roof work is the least predictable job on any list. What the money actually goes into, and what a leak costs to repair in Gqeberha.

Read it

Waterproofing

Roof waterproofing in Port Elizabeth: priced per job, not per square metre

Why this site prices a waterproofing job rather than a square metre, where tiled roofs actually fail on the coast, and what the work costs.

Read it

Doors

Why your door sticks in winter, and why sanding it makes next winter worse

A sticking door is the timber moving with the seasons, not the timber being too big. Sanding the edge clears it now and sets up next winter's return.

Read it

Scope

What a handyman can and cannot legally do in South Africa

The one line that decides whether a job is handyman work or a registered trade, and how to read the answer before you book anyone.

Read it

Assembly

Flat pack furniture assembly in Port Elizabeth: what it costs per item

Flat pack furniture is priced per item, not per box. What a bed and a wardrobe cost to assemble in Port Elizabeth, and why a missing fitting stalls the job.

Read it

Doors

Hanging a door in Port Elizabeth: what it costs and what is involved

A door is a slab of timber going into a frame that has had decades to move. What the job actually involves, and what it costs in Gqeberha.

Read it

Leaks

Water coming through the ceiling: what to do in the first hour

What to do in the first hour when water starts coming through a ceiling, why poking the bulge is a mistake, and how the leak is traced back to its actual source.

Read it

Landlords

A rental maintenance checklist for Gqeberha landlords and agents

Running a rental on a checklist instead of on complaints means one planned visit instead of five separate ones. The list, and what it costs.

Read it

Fitting

Curtain rails and blinds in Port Elizabeth: who fits them and what it costs

Shops sell the rail, the blind and the shelf, then leave you to fit them. What fitting costs per window in Port Elizabeth, and why the wall decides the fixing.

Read it

Small plumbing

A dripping tap in Port Elizabeth: what it costs and when it needs a registered plumber

A dripping tap costs you on the water bill and on your sleep. What the repair costs in Port Elizabeth, and where the plumber has to take over.

Read it

TV mounting

TV wall mounting in Port Elizabeth: what it costs and which wall you have

One number decides most of the price before anyone arrives: what your wall is made of. How to check, and what fitting a bracket actually comes to.

Read it

Odd jobs

No job too small: the odd jobs a handyman actually does

The hardest job to get done in a house is never the big one, it is the single small thing. Here is the actual list, and why batching them pays.

Read it

Coastal

Salt air and rust: what coastal Gqeberha does to doors, windows and fittings

Salt air corrodes the fittings that hold a coastal home together. What the sea does to doors, windows and gate hardware in Gqeberha, and what the repairs cost.

Read it

Cupboards

The cupboard hinge that pulled out of the chipboard

Once the screw holes in chipboard strip, tightening the same screw never works again. Here is which repair holds, and what it costs in Gqeberha.

Read it

Pricing

What a handyman costs in Gqeberha

What the common jobs actually cost in Gqeberha in 2026, why an hourly rate is a bad deal for the person paying, and how to judge a quote you have been handed.

Read it

The list

The small-job list: twelve things worth booking in one visit

The jobs that sit on the fridge door for a year. How long each one takes, which ones belong in one visit, and how to split a long list sensibly.

Read it

Complexes

Complex access: what to have ready before a handyman arrives

Access registers, POPIA requirements, noise hours and lift rules. The details that decide whether a booked visit starts on time or stalls at the boom.

Read it

Send the list. Get a price. Get it done.

One or twenty jobs, it makes no difference. The more you put on the list, the better the visit works out.

WhatsApp your listCall 067 397 3341

No price is agreed until you approve it

Call nowGet a quote