Hanging a door in Port Elizabeth is not a ten minute job, and anyone who says it is has not hung one in an older house. A door is a slab of timber going into a frame that has had decades to move, and the two have to agree with each other before the door will close on its own.
What hanging a door actually involves
A door hangs on hinges set into the edge of the door and the face of the frame, and that joint has to line up in three directions at once. The door must sit at the right height off the floor, at the right depth into the frame so it clears the door stop, and square in the opening so the gap stays even down the hinge side and across the top. Get any one of those wrong and the door drags on the floor, rattles against the stop, or refuses to latch. Each of the three affects the other two, which is why a door adjusted for one problem so often develops a different one a week later.
So the job is measuring before it is cutting. The opening gets checked for square, the frame face gets checked for twist, and the floor gets checked for fall, because a door hung level over a sloping floor will not stay where you put it. Those measurements then go onto a door that is almost never exactly the size of the one that came out. Then comes the fitting: hinge recesses cut to the right depth, plate positions matched to the frame, the door test hung and adjusted, sometimes two or three times, before the latch lines up with the strike plate. Nobody lands that first time on an old frame.
The door gets trimmed, not the frame
The common assumption is that a binding door means the frame needs moving. It does not. A door frame in an older house is tied into the wall and often plastered into it. Moving it means opening the wall, patching and repainting at the very least, and it weakens whatever the frame is fixed to. It also means making good a wall that will never quite match again.
A new door is the part that gets cut. Timber comes off the hinge stile, the lock stile or the bottom edge until the door fits the opening that is already there. The frame stays where it is, because the frame is part of the building and the door is not. Worth knowing before you buy: you can take material off a door, but you cannot put it back on. A door bought on the wrong measurement is not a small problem, it is a second door.
Internal and external, hollow and solid
- Internal doors are light and usually hollow, hung in a frame and expected to stay dry. Their job is privacy rather than security.
- External doors take weather, take a knock, and usually carry a lock that has to line up with a frame that has moved. On the coast, from Summerstrand through to Humewood, salt air corrodes door hardware faster than anything inside the house.
- A hollow core door is a timber skin over a honeycomb core. Light, cheap and perfectly good indoors, but it holds a screw about as well as you would expect. That matters when a hinge has to go back in or a door closer gets fitted.
- Solid and semi solid doors weigh a great deal more, and all of that weight is carried by the hinges into the frame. That means three hinges rather than two, screws long enough to reach the frame rather than just the door, and a frame that is properly fixed. If the frame is loose, a heavy door will find out.
That is the difference people feel without ever naming it. A light internal door forgives a tired frame and a hinge that is a degree out, because there is not enough weight in it to argue. A heavy external door does not. Fit one to a loose frame, or onto hinges that are undersized, and it will show you the problem at the top corner within a few months: a dropped corner, a gap that widens, a latch that stops lining up. Nothing in the frame was ready to carry it.
Locks and latches: where the time actually goes
Most people booking a door job expect the hanging to be the slow part. It is usually the strike plate. The latch has to enter the plate cleanly, which means the plate has to sit at exactly the right depth and the right height in the frame. Too shallow and it holds the door off the stop, so it rattles. Too deep and the latch does not catch at all. The margin is a couple of millimetres, and the only way to find it is to set it, test the door, and adjust. On a replacement door that cycle can happen four or five times, each time with the plate coming off and going back on.
Where a door is being replaced rather than adjusted, the existing lock often needs its mortice recut into the new door, and the handle height has to match what was there or the hole in the frame no longer lines up. Old mortices are rarely where a new lock wants to be, and the timber inside an older door is often closer to the edge than you would like. This is the fiddly half of the job and it is not optional. A door that will not latch is not a door.
If a hinge has pulled out of the frame or out of the door itself, the timber behind it is usually the real problem rather than the hinge. Putting a new hinge into a hole that has already failed will not hold, however good the hinge is.
Old frames in older housing stock
In the older suburbs, Newton Park, Mount Croix, Central and Sidwell, the frames have had decades to move. Timber dries and shrinks, walls settle, plaster cracks, and someone has painted over the top of all of it at least once. A frame that was square in 1970 is rarely square now. That is why a new door off the shelf seldom drops straight in. The opening is no longer a rectangle. It is a slightly tapered, slightly twisted shape, and the only way to find that shape is to measure it properly and check it across the diagonals. It is also worth remembering what the frame has already been through. Doors get slammed, hinges get strained, and at some point someone has packed a hinge plate out with cardboard or matchsticks to get a door closing again. That repair is still sitting in the frame when the next door goes up.
What hanging a door costs
- Door planed and refitted: R400 to R650
- Hinges replaced: R200 to R380
- Sticking door adjusted: R280 to R500
Those are fixed prices per job, agreed before work starts, and they do not move unless the job changes. Hinges, latches, handles or a replacement door are materials, quoted separately and approved before anything is bought. Travelling is already included in the price rather than added on top, so there is no separate charge for the distance.
The short version
Hanging a door is measuring, trimming and fitting, in that order, and the trimming goes on the door rather than the frame. The frame belongs to the building. Most of the time disappears into the strike plate and the final adjustments rather than the cutting, which is why a job that looks like twenty minutes turns into two hours.
Send a photo of the door and the frame on WhatsApp, with the gap at the top and along the side visible in the shot, and you get a fixed price back before anything is booked.
Got a list that needs working through?
Send it on WhatsApp with a photo or two and you get a price back, before anything is booked.
Send the list