A pool filter is the one piece of pool equipment that fails so slowly nobody notices. The pump keeps running, the water looks acceptable from the kitchen window, and the only symptom is that the pool never quite clears after a storm. Then someone opens the filter and finds media that has turned into a concrete block.
This is what filter media does, how to tell when it is spent, and what replacing it costs.
What the filter actually does
The filter is a vessel full of media with water pushed through it. Dirt is trapped in the spaces between the grains. Clean water returns to the pool.
Everything depends on those spaces. Sand media is graded by grain size so the gaps are the right size: big enough for water to pass, small enough to catch fines. Over a season or three, three things happen.
The grains get coated with oils, sunscreen and body fats, which makes them stick together. Channelling develops, where water finds a path of least resistance through the bed and bypasses the rest. And fines work their way deeper until the bed cannot be cleaned by backwashing any more.
At that point the filter is still running and no longer filtering. Water goes in cloudy and comes out cloudy, and the pool gets a chemical treatment every week instead of a mechanical one.
The signs your media is spent
Six things, and most pools show at least three.
- Backwashing does not bring the pressure down as far as it used to.
- The pressure climbs again within a few days of a backwash.
- Cloudy water after rain that used to clear in a day.
- Fine sediment on the floor that returns after vacuuming.
- The pool needs more chlorine than it used to for the same result.
- The media looks like a solid mass instead of loose grains when you open the vessel.
The last one is decisive. If you can push a finger into the sand and it feels like wet cement, no amount of backwashing will fix it.
Sand, cartridge or glass
Three media types, three different maintenance habits.
Sand is the cheapest and the most common. It needs backwashing and it needs replacing every few years. It filters down to a certain particle size and no further, which is why a sand filter can leave a slight haze.
Cartridge filters strain finer and do not need backwashing, but the cartridge has to be removed and hosed, and eventually replaced. They suit smaller pools and places where water restrictions make backwashing awkward.
Glass media is the newer option. It lasts longer than sand, filters finer, and uses less water to backwash. It costs more up front, and the difference in water clarity is real rather than marketing.
Which one is right depends on the filter you already own. A sand filter takes sand or glass. A cartridge filter takes cartridges. They are not interchangeable, and nobody should be selling you a media change without looking at the label on the vessel.
When the pressure gauge lies
The gauge is the only instrument on the filter and it is the one most likely to be broken. A gauge that reads zero with the pump running is dead, and with a dead gauge you cannot tell when to backwash, which is how media gets destroyed in the first place.
Two things worth knowing. First, a gauge reading needs a clean baseline: note the pressure right after a backwash and after a media change, and compare against that rather than against a number you read online. Second, gauges fail quietly, and a replacement is one of the cheapest parts on the system.
If the gauge is dead and the media has not been changed in years, treat both as one job. Doing the media and leaving the dead gauge in place means the next owner of the pool is guessing again.
What a proper backwash looks like
Backwashing is not "run it for a minute". It is a sequence, and done properly it extends the life of the media considerably.
With the pump running, switch the valve to backwash and watch the sight glass. Water comes out dirty, then clears. When it runs clear, the backwash is done. Then switch to rinse and run it briefly before returning to filter, because rinse settles the bed and stops the first burst of dirt going back into the pool.
Two mistakes shorten media life. Backwashing on a schedule instead of on pressure, which wastes water and does not clean the bed properly. And forgetting to rinse, which sends a slug of dirty water into the pool every time.
How often
The honest answer is that it depends on use, and the manufacturers' intervals assume a well-kept pool.
A busy family pool in Gqeberha, used daily through summer with the south-easter blowing grit into it, will go through media faster than a pool used on weekends. Three to five years for sand is a reasonable expectation. Glass media lasts longer.
What shortens it: running the pump with a dirty basket, letting the pool sit green for weeks, using cheap flocculants badly, and never backwashing properly because the valve position was wrong.
What extends it: correct backwashing, a clean basket, and not letting the pool turn.
What the job involves
Filter media replacement is a physical job rather than a technical one, and the awkward part is the removal.
The vessel is drained, the old media is dug out and carried away, the laterals at the bottom are checked for cracks, the correct graded media goes back in to the right depth, and the valve is reassembled. A cracked lateral is worth catching at this point, because a filter that spits sand into the pool is usually a lateral problem rather than a media problem.
Add the backwash and a proper rinse before the pool goes back into service, and it is a two hour job on most residential filters.
What it costs
Our published range for replacing filter sand or media is R900 to R2,200, and the spread reflects the size of the vessel and the media chosen.
For context on the rest of the pool work we do:
- Pool cleaned, vacuumed and brushed: R350 to R800
- Pool pump seal, O-rings or impeller replaced: R900 to R1,800
Materials are quoted separately and approved before anything is bought, which matters here because media is priced by weight and there is no point in guessing.
Why this is the job to do in November
December is when a pool has to work. Family arrives, the pool gets used four times a day, and a filter that has been limping through winter has no margin left.
Changing media in November means the pool has a month to settle before it has to perform, and any issue with the laterals or the valve shows up while there is still time to deal with it.
Doing it in the last week of December means doing it while people are swimming and nobody wants the pump off.
What to check while the filter is open
If the media is coming out anyway, four things are worth checking in the same visit:
- The laterals at the bottom of the vessel, for cracks and loose connections.
- The multiport valve O-rings and spider gasket, which are the usual cause of water leaking from the waste port.
- The pressure gauge. A gauge that reads zero when the pump is running is a gauge that needs replacing, and without it you cannot tell when to backwash.
- The pump lid O-ring, which is the cheapest thing on the whole system and the most common cause of a pump losing prime.
None of this is upsell. It is the work that makes one visit worth more than three.
Book it
WhatsApp 067 397 3341 with a photo of the filter label and the pool volume if you know it. We will tell you which media it takes and what the job costs, and if the laterals are suspect we will say so before the work starts rather than after.
A pool filter is not glamorous work. It is the reason the pool looks good in December.
Got a list that needs working through?
Send it on WhatsApp with a photo or two and you get a price back, before anything is booked.
Send the list